tongue and groove floor decking span tables

Structural Wood Corporation: Wood Decking

Solid 2x6 decking is available from SWC in Douglas Fir, Southern Yellow Pine and Spruce. Laminated roof deck in 3x6 and 4x6 Fir / Larch is also available from Structural Wood Corporation's inventory. Wood decking is cut in a tongue and groove interlocking pattern along the edges of the pieces. End matching is specified to prevent the material

Get Quotes

3x6 Tongue and Groove Douglas Fir Roof Deck

3x6 Tongue and Groove Douglas Fir Roof Decking. 100SF min order. Available in 3x6 and 4x6 Please call 1-877-640-4095 .

Get Quotes

tongue and groove decking span tables

timber tongue and groove decking must be · Span tables for x X and rafter span tables for itself and the roofing materials over that increased span . Does anyone know where I can find span tables for thick tongue and groove floor deck plank Maybe a website for a manufacturerI have googled it and ha.

Get Quotes

WCD 2 - Tongue and Groove Roof Decking

Nominal three and four inch decking is especially well adapted for use with glued laminated arches and girders and is easily and quickly erected. This document contains all that's needed to design and construct tongue and groove wood roof decking, including span and load tables.

Get Quotes

Tongue and Groove Decking The Building Code Forum

 · Does anyone have experience using tongue and groove decking for roof sheathing? IRC Table R803.1 lists 1 1/2" T and G for rafter spans up to 72". I am looking to space rafters at 72" however I cannot find any information on diaphragm strength of the T and G decking. Just wondering if anyone has used this decking to act as the roof diaphragm.

Get Quotes

2x6 t and g roof deck - JLC-Online Forums

 · For a given decking span length, LL requirement and a given deflection criteria; the bending stress is approx. such-n-such, and you must select a material with at least the given modulus of elasticity and a higher allowable bending stress, for the decking to meet the IBC. That†s how you should read that table.

Get Quotes

Specialty Products - Southern Pine

Southern Pine double-beaded and V-groove patterns are classics for applications such as wainscoting and ceiling interior and porch . Tongue-and-groove products are manufactured in a variety of grades. C and Btr and D grades are excellent for painting and staining. The No.2 grade offers an economical alternative, while providing a rustic look.

Get Quotes

2 x 6 TIMBER DECKING - Structural Wood

2 x 6 TIMBER DECKING BY: STRUCTURAL WOOD SYSTEMS It is machined with a single tongue-and-groove, a V-Joint face, and is END MATCHED allowing the use of RANDOM LENGTH pieces. The spans or on alternate supports. This decking is to be installed with tongues upward on sloped or pitched roofs and outward from

Get Quotes

Tongue and Groove Roof Decking - WCD2 - TinyTimbers

4 TONGUE AND GROOVE ROOF DECKING Two-Span Continuous All pieces are supported on three supports. All end joints occur in line on every other support Figure 6 . Controlled Random Layup This arrangement is applicable to 4 or more supports 3 or more spans . With less than 4 supports, a special pattern requiring specified lengths must be used. Joints

Get Quotes

3 1/2" tongue and groove floor deck plank - Structural

Does anyone know where I can find span tables for 3 1/2" thick tongue and groove floor deck plank . Maybe a website for a manufacturer. I have googled it and have not had any luck. This is a commercial application and trying to span 4 to 6 feet.

Get Quotes

Structural Decking - Western Wood Products Association

Tongue and Groove Structural Decking. Structural Decking also known as "roof decking" - should not be confused with lumber intended for residential and non-residential outdoor decks. Standard structural decking patterns are 2" nominal, tongued and grooved T and G and 3" and 4" double T and G products, available with vee or eased edges, to meet

Get Quotes

FS Industries - PLYWOOD DECKING

TONGUE AND GROOVE ALL FOUR SIDES Plywood: Full face 48" x 96" x 1 1/8" thick with touch - sanded surface. These cost efficient, highly durable sheets are manufactured to FSI specifications. They provide an attractive rigid floor surface that does not require joints to occur over support beams.

Get Quotes

Tongue and Groove Decking - S.I. Storey Lumber

Tongue and groove wood decking should be installed with the tongue up on sloped roofs and outward in direction of laying on flat roofs. Pattern faces should be down and exposed on the underside. Each piece of 2" thick decking should be toenailed through the tongue and face nailed with one 16d common nail per support. Each piece of 3" and 4

Get Quotes

2x8 tongue and groove span chart.pdf

 · Source #2: 2x8 tongue and groove span chart.pdf FREE PDF DOWNLOAD. Seven Trust Decking Prices well manufactured . tables for the nominal thickness and span under consider-.Laminated or Tongue and Groove APA Engineered Wood Construction Guide 2x8 tongue and groove span chart.pdf FREE PDF DOWNLOAD NOW Source #2: 2x8 tongue and groove span chart.pdf

Get Quotes

Product Details

Product List