replacing riser and treads on deck stairs

Replacing Stair Risers DoItYourself.com

The next step necessary to replace stair risers is to remove the existing ones. This can be done with a hammer and chisel by positioning the point of the chisel in the joint between the treads and the stair risers. You will find that the riser is often fitted slightly behind the lip of the tread.

Get Quotes

DIY Central How To Replace Stair Treads - DIY Central

Replacing stair treads may be necessary due to age or wear, or for esthetic reasons. Some people remove the carpet that covers their stairs and find that the treads and risers are of rough construction or severely damaged by carpet tack strips and staples. In all these cases, you may want or need to replace your stair treads.

Get Quotes

Remove and replace stair treads - Fine Homebuilding

 · Great information from all of you. Sunday I will remove the treads and risers. Hopefully the glue won't give me too much trouble. I'll put them back with one or two screws in each and then next weekend I'll put down the new treads and risers. Based on the info you gave me I will make my own stair gauge and cut the treads with a circular saw.

Get Quotes

Common Deck Stair Defects Professional Deck Builder

 · Before getting into deck stair defects, let’s look at how DCA 6 recommends that stairs should be built, starting with the stringers, risers, treads, landings, and the components that support them Figure 1 . When I’m evaluating a deck stair, this is where I start.

Get Quotes

Rehabbing a Rotted Porch Stair Professional Deck Builder

 · Making and Installing Treads and Risers. The old risers were wood. Although only the bottom riser had rotted, I decided to replace them all with PVC Kleer Lumber; 866/553-3770, kleerlumber.com . PVC won’t rot, decay, crack, or warp over time, plus it takes paint beautifully and it can be laid on the ground and up against soil without any

Get Quotes

How to replace stair treads in a staircase part 1

 · Although this staircase was poorly constructed by the builder, I was able to replace the MDF stair treads with some nice tigerwood ones. I used a lot of liquid nail so that they would stay in

Get Quotes

Replace Deck Stairs in 9 Steps DoItYourself.com

Replace Deck Stairs in 9 Steps Building deck stairs is quite a simple job. Replacing them is even simpler because you have a template to work from. If the stairs are hazardous you should remove them while you build the replacements. Tie some warning tape across the gap in the rail so people don’t step off the deck and fall. The risers are

Get Quotes

How to Replace a Single Stair Tread on a Set of Stairs

Wooden stair treads wear out from the thousands of steps taken on them over your home's lifetime. The wood cracks and splits, weakening the step. Cracked steps often squeak loudly when weight is

Get Quotes

Replacing treads on a mortised staircase - JLC-Online Forums

 · Re: Replacing treads on a mortised staircase Best job = entire new stair but this is a step by step approach to a good cost/value repair after all this is the “production approach†forum . We typically do not recommend riser and tread replacement leaving the carriage in place with a boxed stair.

Get Quotes

Replacing Stair Risers DoItYourself.com

STEP 1 PLANSTEP 2 DISASSEMBLYSTEP 3 ORGANIZESTEP 4 CUT REPLACEMENTSSTEP 5 INSTALLStart by planning how you intend to complete the process by examining the staircase. Take the opportunity to consider the manner in which the stairs are constructed so that you can determine whether the banister needs to be removed. Locate the joins where the wood pieces meet each other. In most cases, you will need to begin at the top when removing the risers and work your way down.

Get Quotes

How should stair treads and risers be assembled? - Home

When assembling stair treads and risers, is it better to have the tread tucked under the riser or have the riser tucked in between the tread and the stringer riser backing? I am inclined to think the former because that way the tread gets more framing support but the way my current stairs are assembled is the latter, hence my uncertainty. To quote from "A Treatise on Stairbuilding and Handrailing" Mowat, 1900 : Whenever possible each tread and riser should be jointed together, glu 3We installed it so the tread goes under the riser. We installed hardwood stairs in our home and we cut the bottom of the riser at a slight angle to 2The answers of the tread then riser SEEM to make sense, but consider this: A properly installed tread will not come off before the lip breaks off .2Treads and risers install should start at the bottom step. First the riser and then the tread. However, on the tread you leave a 1/4 inch gap on th 1If you install the tread first and then put in the riser, the riser will add stability to the tread by holding down the back of the tread; then it 0Since you probably have to rip both the tread and the riser to size, I would install a tread and then the riser on top. So the ripped edge of trea 0It comes down to flow. From top to bottom on any assembly you should build it so water flows downward and not inside the assembly. If the riser is 0I like the "water flow" answer above, because it makes sense. However, if you are retreading a staircase, the overtreads often have a lip below th 0Water flow over the tread which overhang these gaps you guys are talking about. If the tread happen to slope backward, no gap will prevent water fr 0

Get Quotes

Step by Step: How to Install Wood Treads and Risers for

Step by Step: How to Install Wood Treads and Risers for Boxed-In Stairs. Details Steve Marley If it's too snug, remove and trim it as necessary. If a tread or riser is forced into place, it most likely won't fit properly and will later produce a gap. Back-cut a slight angle on the riser ends approximately 1/4 inch behind the face. This

Get Quotes

Product Details

Product List