Step 1 Cut the track to the correct length. The first step is to cut the track to the right length. If installing the transition in a doorway cut the track about 1/2 inch short at each end. The space between the laminate and the ceramic tile should allow the track to have a space of 1/4 inch from the laminate and tile.
· How to Tile over Tile. If you want to replace an old tiled surface, you might think that you can only do so by painstakingly removing the old tile first. As long as the old surface is in a fairly sturdy condition, however, you can lay
With expertly rounded or beveled edges, this tile threshold piece offers a seamless transition from your shower pan, kitchen, bathroom or fireplace area. Made with the same care and quality as the matching tile, durable curbs and thresholds are ideal for high-traffic areas.
Install the Lath. Before cutting it, make sure the lath is oriented correctly: with the cheese-grater-like "cups" facing up so that the scales feel rough as you run your hand away from the door and down the side. Use a powder-actuated nailer and a hammer to nail down the lath every 6 to 8 inches.
Push the first tile into the combed mortar bed with a twisting motion. Using a protective scrap piece of lumber, tap the tile with a mallet to set it. For the first tile only, pull it back up to make sure the combed mortar is think enough to cover the entire bottom of the tile.
Step 18 Lay Floor Tile. Press the tiles firmly into the mortar to make sure they conform to the slope of the floor. Line up all the edges with a 2-foot straightedge and let the mortar cure overnight. Grout the tiles with latex-modified grout, cleaning off the excess and wiping the grout haze.
If you want to install laminate flooring on your stairs I would recommend that you do a lot of research and find the information you will need to do it correctly. Installing laminate flooring on stairs can be tedious and time consuming and is a lot different than installing laminate flooring on a floor.
· Because the top steps are likely more visible than the bottom step, start on top and work your way down. Begin setting tiles into the thinset mortar on the sides of the steps. Start at the top and work your way downward. Try to lay out tile so the vertical gaps between tiles align.
Once the tile has been set you can apply the grout and sealer. Once the grout and sealer have been applied, the shower pan should look like the diagram below. Note that the same steps apply to vinyl liners as to hot mopped shower pans. West Coast Shower Pans has expert hot moppers to help make your new shower installation a reality.
· All of the supplies and steps you need for installing sheet vinyl flooring over old tile yourself for a temporary fix. Favorite project EVER Okay, I say that about probably 50% of every project we do around here, but this one is definitely up there on the charts of most-transformative-for-least-amount-of-money.
· Install the tiles on the stair treads, starting at the top tread and working your way downward. Set a bullnose tile on each side of the centerline and work your way toward the sides, making sure to conceal the step-side tiles with the tread tiles.
· Install the underlayer. To install the underlayer, you will need to use a special underlayer stapler with ⅞-inch staples; you will use approximately 16 staples per square foot of underlayer. You should never use nails or screws in the underlayer, as these will cause bumps in the vinyl flooring.
· Step 1. Inspect the tile floor and make sure there are no loose tiles; the existing tile must be in good shape for re-tiling. Step 2 Clean the tile thoroughly to remove any wax or build-ups on the tile floor. Scuff or sand the tile to make the surface a little rough; this helps the new tile bond to the old tile.
Installation: Lay threshold molding in place to determine a proper fit. The threshold molding should overlap the flooring by 1/2" to 3/4" leaving the balance for expansion. To attach the threshold, nail into the subfloor behind the lip of the molding. Be sure when nailing not to obstruct the floors expansion space.
Related To: This type of threshold is screwed down through the carpet and angled so that it can provide a smooth transition from one height to the next. Another option when installing carpet next to tile is to butt the carpet against the tile and place a marble threshold over the edge. Marble thresholds typically cost about $10
How to Install Tile Thresholds. Press the threshold in place. Ensure that there is even spacing on either side of the door against the casing, and at least 1/8 inch of space against the termination of the tile installation. Allow the threshold to set for 24 hours.
· The easiest-to-install threshold is a strip of metal or thin wood that lies on top of the two floor surfaces. For a more graceful solution, use a flush threshold, which is at the same level as the two surfaces. Installing a flush threshold calls for more-careful cutting, since the tiles and the other surface must meet it precisely.
additional mortar with the notched side. Use the proper sized notched trowel for the tile or stone to ensure full bedding of the. tile. Back butter large tiles >8" x 8" >200 mm x 200 mm to provide full bedding and firm support.